The square footage on a strata plan and a measured square footage often differ because they measure different things. The strata plan area runs to the middle of the walls and can include patios, storage rooms or parking. A measurement of the living space may run to the outside or the inside face of the walls. Neither number is wrong on its own; the listing has to say which one it uses.
For BC realtors, the gap is more than a technicality. Square footage is a common source of complaints about listings, and the BC Financial Services Authority (BCFSA) has disciplined licensees over it. This guide explains where each number comes from, why they drift apart, and how to present size in a strata listing without misleading buyers.
Where the strata plan number comes from
Every strata lot in BC is shown on a strata plan filed in the Land Title Office, and the plan gives each lot a square area. Under section 68 of the Strata Property Act, unless the strata plan shows otherwise, the boundary between a strata lot and a neighbouring lot or common property runs midway through the structural part of the wall, floor or ceiling that separates them.
In practice, the plan area of a typical apartment-style unit:
- includes half the thickness of the walls shared with neighbours and the corridor
- includes interior walls, closets and the space taken up by stairs
- can include more than the living space
That last point catches people out. BCFSA's practice resource on property measurements notes that some developers have included balconies, large patios and even parking stalls in strata lot measurements, and that some plans carry a note saying the areas shown within lots are total areas that include patios, carports and storage rooms. When a plan says that, BCFSA advises finding the plans that give the included areas and deducting them, so buyers get the correct area of the living space.
Where a measured number comes from
A measured square footage is whatever someone records on site with a laser, tape or scanner, and the result depends on the method. BCFSA's consumer guide on property measurements says there is no single standard way of measuring a property. There are general guidelines by property type, but real estate professionals and measuring companies use their own methods.
The practice resource gives one example standard: floor area based on the exterior dimensions of each level, including interior walls, with the centre line of common walls used for attached units and garages excluded. Other measurers report interior area, from wall face to wall face. Measured that way, the same unit comes out smaller, because the wall thickness is left out.
So before comparing two numbers, find out how each was arrived at. A 30 or 40 square foot gap between a centre-of-wall figure and an interior figure can be explained by wall thickness alone. A gap of several hundred square feet cannot.
Why the two numbers drift apart
These are the usual reasons a measurement won't match the strata plan:
- Wall thickness. The plan area runs to the middle of the demising walls, while interior measurements stop at the drywall. Units with a lot of perimeter wall, such as corner units or long, narrow layouts, show a bigger gap.
- Included extras. If the plan's lot area includes a patio, storage room or parking, the living space is smaller than the plan figure.
- Built differently from the plans. BCFSA warns that strata lot measurements taken from Land Title Office plans have occasionally been found to be incorrect, for example when a builder deviated from the plans filed at registration. Its advice is to check plan figures by physically measuring the unit.
- Limited common property. Balconies, patios and parking spaces designated as limited common property (LCP) sit outside the strata lot even though the owner has exclusive use of them. They should not be added to the lot's area, but they are worth listing separately.
- Multi-level units. For townhouses and other multi-level strata lots, the area of each floor is added together. A missed level, a double-counted level or stair openings handled differently will change the total.
- Data entry. A mistyped dimension can produce a figure that matches neither the plan nor the home.
A real case: 1,375 square feet listed, 1,032 measured
BCFSA's advertising guidelines include a case in which an MLS listing showed 1,375 square feet. After completion, the buyers' insurer told them the home was about 1,000 square feet, and the buyer's representative measured 1,032. The listing licensee's file had a perimeter of 22 by 47 feet, about 1,034 square feet. The likely cause was the perimeter being entered as 22 by 67, less roughly 99 square feet for the staircase. BCFSA found contraventions of the rules on acting with reasonable care and skill and on false or misleading advertising.
The lesson isn't that strata plans can't be trusted. It's that every size figure in a listing needs a known source, and someone has to check it against the home.
How BCFSA suggests describing a strata unit's size
The practice resource suggests stating the strata lot's square area together with any exclusive-use areas designated as LCP for that lot. Its example describes a strata lot of 1,400 square feet with the exclusive use of a balcony, a large patio and two parking spaces designated as limited common property. Written that way, buyers can see what is inside the lot and what they only have the use of.
BCFSA also advises care with common property covered by a short-term exclusive use agreement. Continued use isn't guaranteed, and the seller can't assign the agreement to a buyer without the strata corporation's consent, so it shouldn't be presented as part of what is being sold.
A practical workflow for strata listings
- Get the strata plan for the lot from the Land Title Office and read every note on the sheet, not just the number inside the lot.
- Deduct included extras if the plan says lot areas include patios, carports or storage rooms.
- Measure the unit and compare it with the plan. If the difference is bigger than wall thickness would explain, find out why before the listing goes live.
- Decide which figure goes where. One common approach is to quote the strata plan area as the lot size and use measured figures for room sizes and the floor plan. Whatever you choose, use the same figures on the MLS, feature sheet, brochure and property website.
- Say how the number was arrived at. BCFSA's consumer guide tells buyers to ask how a measurement was arrived at and what it includes. A short note answers that question before it is asked, for example: "Strata lot area per strata plan; room dimensions measured on site."
- List LCP separately: balcony, patio, parking stalls and storage locker, each marked as limited common property where that applies.
- Keep the file. Save the strata plan page, the on-site measurements and your notes on which figure appears where.
Where a floor plan and room report help
A measured floor plan doesn't replace the strata plan, but it gives buyers the layout and room sizes the strata plan doesn't show, and it gives you an independent on-site measurement to check against the plan figure.
Our LiDAR floor plans are captured on site and deliver a 2D floor plan with measurements, priced by square footage. As of November 2026 the live price starts at $185 for an 800 sq ft home. The property measurement report adds a room-by-room list of dimensions as a flat-rate add-on, currently $50. Both prices are before tax and travel fees; the pricing page calculates the exact figure for the home's size. Our guide to property reports and room dimensions covers how to use the numbers with buyers.
Whoever measures the home, ask them which method they use and whether the total includes walls, stairs and unfinished space, then put that in your listing notes. This matters most in tower-heavy markets such as Vancouver and Burnaby, where buyers can compare several units in the same building and will notice when sizes are stated in different ways.
Strata square footage checklist
- Strata plan pulled and every note on the lot's sheet read
- Patios, carports, storage or parking deducted if the plan includes them
- Unit measured on site and compared with the plan
- Any gap larger than wall thickness explained before listing
- LCP areas listed separately from the strata lot area
- Source of each figure stated in the listing
- Same figures used on the MLS, feature sheet, brochure and website
- Strata plan, measurements and notes kept on file



